This website <https://www.panasonic.com/nz/> ("Site Page") is developed and owned by Panasonic Corporation and its affiliates (“Panasonic”, “us”). By accessing the Site Page, you agree to be bound by these Terms and Conditions of Use, the Privacy Statement, and any other terms and legal notices on the Site Page.
PT-VX415NZA
| Power supply | 100-240 V AC, 50/60 Hz | |
|---|---|---|
| Power consumption | 100-120 V AC: 300 W, 220-240 V AC: 280 W (0.4 W when STANDBY MODE set to ECO,*1 5 W when STANDBY MODE set to Network, 14 W when STANDBY MODE set to Normal.) | |
| LCD panel | Panel size | 16.0 mm (0.63 in) (4:3 aspect ratio) |
| Display method | Transparent LCD panel (x 3, R/G/B) | |
| Pixels | 786,432 (1,024 x 768) x 3, total of 2,359,296 pixels | |
| Lens | 1.6x manual zoom (throw ratio: 1.2-1.9:1), manual focus, F 1.60-2.12, f 15.30-24.64 mm | |
| Lamp | 230 W x 1, lamp replacement cycle (lamp power: Normal/Eco1/Eco2): 4,000 hours/5,000 hours/6,000 hours*2 | |
| Screen size (diagonal) | 0.76-7.62 m (30-300 in), 4:3 aspect ratio | |
| Brightness*3 | 4,200 lm (input signals: PC, lamp power: Normal, picture mode: Dynamic) | |
| Center-to-corner uniformity*3 | 85% | |
| Contrast*3 | 4,000:1 (full on/off) (input signals: PC, lamp power: Normal, picture mode: Dynamic, IRIS: On) | |
| Resolution | 1,024 x 768 pixels*4 | |
| Scanning frequency | HDMI | fH: 15-80 kHz, fV: 50-85 Hz, dot clock: 162 MHz or lower |
| RGB (analog) | fH: 15-100 kHz, fV: 50-100 Hz, dot clock: 162 MHz or lower (Signals exceeding the dot clock rate of 140 MHz are downsampled.) | |
| YPBPR (YCBCR) | fH: 15.75 kHz, fV: 60 Hz [480i (525i)] fH: 15.63 kHz, fV: 50 Hz [576i (625i)] fH: 45.00 kHz, fV: 60 Hz [720 (750)/60p] fH: 33.75 kHz, fV: 60 Hz [1080 (1125)/60i] fH: 28.13 kHz, fV: 25 Hz [1080 (1125)/25p] fH: 27.00 kHz, fV: 48 Hz [1080 (1125)/24sF] fH: 67.50 kHz, fV: 60 Hz [1080 (1125)/60p] fH: 31.50 kHz, fV: 60 Hz [480p (525p)] fH: 31.25 kHz, fV: 50 Hz [576p (625p)] fH: 37.50 kHz, fV: 50 Hz [720 (750)/50p] fH: 28.13 kHz, fV: 50 Hz [1080 (1125)/50i] fH: 27.00 kHz, fV: 24 Hz [1080 (1125)/24p] fH: 33.75 kHz, fV: 30 Hz [1080 (1125)/30p] fH: 56.25 kHz, fV: 50 Hz [1080 (1125)/50p] | |
| Video/S-Video | fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60], fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM] | |
| Optical axis shift | 9:1 (fixed) | |
| Keystone correction range | Vertical: ±40° (±30° when using Easy Setting) (maximum value of XGA input), horizontal: ±30° (±20° when using Easy Setting) (maximum value of XGA input) | |
| Installation | Ceiling/floor, front/rear | |
| Terminals | HDMI IN | HDMI 19-pin x 1 (compatible with HDCP, Deep Color) 480i*5, 480p, 576i*5, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p, 1080/60p, 1080/50p, VGA (640 x 480)-WUXGA (1,920 x 1,200),*6 audio signal: linear PCM (sampling frequencies: 48 kHz, 44.1 kHz, 32 kHz) |
| COMPUTER 1 IN | D-sub HD 15-pin (female) x 1 (RGB/YPBPR/YCBCR x 1) | |
| COMPUTER 2 IN / MONITOR OUT | D-sub HD 15-pin (female) x 1 (RGB x 1), (input/output selectable using on-screen menu) | |
| VIDEO IN | Pin jack x 1 (Composite VIDEO) | |
| S-VIDEO IN | Mini DIN 4-pin x 1 (S-VIDEO) | |
| AUDIO 1 IN | M3 x 1 (L-R x 1) | |
| AUDIO 2 IN (MIC IN) | M3 x 1 (L-R x 1) for audio input or for microphone connection (variable) | |
| AUDIO 3 IN | Pin jack x 2 (L, R x 1) | |
| AUDIO OUT | M3 x 1 (L-R x 1) for output (variable) | |
| SERIAL IN | D-sub 9-pin (female) x 1 for external control (RS-232C compliant) | |
| LAN | RJ-45 x 1 (for network connection, 10BASE-T/100BASE-TX, compliant with PJLink™) | |
| USB A | USB type-A (for the USB Memory Viewer) x 1 | |
| USB B | USB type-B (for the USB Display) x 1 | |
| Built-in speaker | 4.0 cm (1-9/16 in) round shape x 1, output power: 10.0 W (monaural) | |
| Noise level*3 | 35 dB (lamp power: Normal), 29 dB (lamp power: Eco1, Eco2) | |
| Cabinet materials | Molded plastic | |
| Dimensions (W x H x D) | 352 x 98.0*7 x 279.4*8 mm (13-27/32 x 3-27/32*7 x 11*8 in) | |
| Weight*9 | Approx. 3.4 kg (7.5 lbs) | |
| Operating temperature | 0°C-40°C [32°F-104°F] (less than 1,400 m [4,593 ft] above sea level, HIGH ALTITUDE MODE: OFF), 0°C-30°C [32°F-86°F] (between 1,400 m and 2,000 m [4,593 ft and 6,562 ft] above sea level, HIGH ALTITUDE MODE: HIGH 1), 0°C-30°C [32°F-86°F] (between 2,000 m and 2,700 m [6,562 ft and 8,858 ft] above sea level, HIGH ALTITUDE MODE: HIGH 2) | |
| Operating humidity | 10-80 % (no condensation) | |
| Wireless | Standard | 2.4 GHz: IEEE802.11b/g/n, 5.0 GHz: IEEE802.11a/n |
| Infrastructure mode | WPA-PSK (TKIP/AES), WPA2-PSK (TKIP/AES), 128 bit/64 bit WEP, WPA-EAP/WPA2-EAP (PEAP [MS-CHAPv2/GTC], EAP-FAST [MS-CHAPv2/GTC], EAP-TTLS [MD5/MS-CHAPv2]) 128bit/64bit | |
| Supplied accessories | Power cord x 1*10, wireless remote control unit x 1, batteries (AAA/R03/LR03 type x 2), computer cable x 1, Software CD-ROM (Logo Transfer Software, Multi Projector Monitoring & Control Software, Wireless Manager ME 6.0) | |
| *1 | When the Standby mode is set to Eco, network functions such as power on over the LAN network will not operate. Also, only certain commandscan be received for external control using the serial terminal. | |
| *2 | This is the maximum value when the lamp is turned on for 2 hours and off for 0.25 hours. If the lamp is turned on more times or kept on for a long time,the lamp replacement cycle will shorten. The usage environment affects the duration of the lamp. | |
| *3 | Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards. | |
| *4 | Input signals that exceed this resolution will be converted to 1,024 x 768 pixels. | |
| *5 | Only compatible with dot clock frequency of 27 MHz (pixel repetition signal). | |
| *6 | Compliant with VESA CVT-RB. | |
| *7 | With legs at shortest position. | |
| *8 | Including protruding parts. | |
| *9 | The above values are averages. Actual values may be different according to the product. | |
| *10 | Power cords available (x 2) for the UK and Asia only. | |
| Caution | Do not install the projector in locations that are subject to excessive water, humidity, steam or oily smoke. Doing so may result in fire, malfunction or electric shock. | |
| NOTES ON USE | 1 The projector uses a high-voltage mercury lamp under high internal pressure. This lamp may break, emitting a popping sound, or fail to illuminate, due to impact or extended use. 2 The high-wattage lamp becomes very hot during operation. Please observe the following precautions: • Never place objects on top of the projector while it is in operation. • Make sure there is an unobstructed space of 1,000 mm (39-3/8 in) or more around the projector’s exhaust openings. • If stacking projector units, care must be taken to provide the recommended space between units. These space requirements also apply to installation where only one projector unit is operating at one time and the other unit is used as a backup. • If the projector is placed in a box or enclosure, the temperature of the air surrounding the projector must match the operating temperature listed in the specifications table during use. Also, make sure the projector’s intake and exhaust openings are not blocked. Ensure there is sufficient ventilation to prevent hot air from the exhaust openings being recirculated into the intake opening. 3 The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods. • The lamp replacement cycle varies greatly depending on individual lamp characteristics and usage conditions. • The brightness of the lamp will gradually decrease with use. 4 Due to natural characteristics of lamps, screen brightness may fluctuate. This is not an indication of faulty lamp performance. | |
Copyright © 2024 Panasonic New Zealand
This website <https://www.panasonic.com/nz/> ("Site Page") is developed and owned by Panasonic Corporation and its affiliates (“Panasonic”, “us”). By accessing the Site Page, you agree to be bound by these Terms and Conditions of Use, the Privacy Statement, and any other terms and legal notices on the Site Page.