Specs - PT-LX22EA Portable

Panasonic values your privacy and your trust is important to us. We use cookies to enhance your website experience. By clicking “Accept all cookies”, you agree Panasonic can store cookies on your device and disclose information in accordance with our Privacy Policy. OK Learn More

AddedRemoved

See product page

Copy URL

PT-LX22EA

General	Power supply		100 - 240 V AC, 50/60 Hz
	Power consumption		287 W (0.47 W in Eco standby mode*¹, 7.1 W in Serial standby mode.)
	LCD panel	Panel size	14 mm (0.55 inches) diagonal (4:3 aspect ratio)
		Display method	Transparent LCD panel (x 3, R/G/B)
		Pixels	786,432 (1,024 × 768) x 3, total of 2,359,296 pixels
	Lens		1.2x manual zoom, manual focus, F 2.10-2.25, f 19.11-22.94 mm
	Lamp		230 W × 1, lamp replacement cycle (lamp power: High, Normal/Eco): 3,000 hours/4,000 hours*²
	Screen size (diagonal)		0.76-7.62 m (30-300 inch)
	Brightness*sup3/sup		2,200 lm (lamp power: High)
	Center-to-corner uniformity ratio*sup3/sup		85 %
	Contrast ratio*sup3/sup		500:1 (full on/full off, lamp power: High)
	Resolution (RGB)		1,024 × 768 pixels*⁴
	Scanning frequency	RGB (analog)	fH: 15-100 kHz, fV: 50-100 Hz, dot clock: 140 MHz or lower (Signals exceeding the dot clock rate of 140 MHz are downsampled.)
		YPsubB/subPsubR/sub (YCsubB/subCsubR/sub)	fH: 15.75 kHz, fV: 60 Hz [480i(525i)] fH: 31.50 kHz, fV: 60 Hz [480p(525p)] fH: 45.00 kHz, fV: 60 Hz [720(750)/60p] fH: 33.75 kHz, fV: 60 Hz [1080(1125)/60i] fH: 15.63 kHz, fV: 50 Hz [576i(625i)] fH: 31.25 kHz, fV: 50 Hz [576p(625p)] fH: 37.50 kHz, fV: 50 Hz [720(750)/50p] fH: 28.13 kHz, fV: 50 Hz [1080(1125)/50i]
		Video/S-Video	fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60], fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
	Optical axis shift		6:1
	Keystone correction range		Vertical: ±30° (±20° when Real-Time Keystone)
	Installation		Ceiling/floor, front/rear
	Terminals	COMPUTER IN 1/ S-VIDEO IN	D-sub HD 15-pin (female) x 1 (RGB/YPBPR/YCBCR /S-VIDEO x 1) (The D-Sub/S-VIDEO conversion cable ET-ADSV is required for inputting S-VIDEO signals.)
		VIDEO IN	RCA pin × 1 (Composite VIDEO)
		SERIAL IN	D-sub 9-pin (male) × 1 for external control (RS-232C compliant)
	Noise level		37.0 dB (lamp power: High), 34.1 dB (lamp power: Normal), 29.0 dB (lamp power: Eco)
	Cabinet materials		Molded plastic
	Dimensions (W × H × D)		349 x 105 x 247 mm (13.7" x 4.1" x 9.7") (with legs at shortest position, not including protruding parts)
	Weight		Approximately 2.90 kg (6.39 lbs)
	Operating environment		Operating temperature: 5°C-35°C (41°F-95°F), operating humidity: 20%-80% (no condensation)
	Supplied accessories		Power cord x 1*5, wireless remote control unit, batteries (AAA/R03/LR03 type × 2), VGA cable x 1, filter cover, software CD-ROM (Logo Transfer Software)
NOTE			1 When Standby mode is set to Eco, only certain commands can be received for external control using the serial terminal. 2 The values given for the recommended lamp replacement cycles are maximum. The usage environment affects the lamp replacement cycle. 3 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards. 4 Input signals that exceed this resolution will be converted to 1,024 x 768 pixels. *5 Power cords available (x 2) for the PT-LX26EA/LX22EA. Caution Do not install the projector in locations that are subject to excessive water, humidity, steam or oily smoke. Doing so may result in fire, malfunction or electric shock. NOTES ON USE 1 The projector uses a high-voltage mercury lamp under high internal pressure. This lamp may break, emitting a popping sound, or fail to illuminate, due to impact or extended use. 2 The high-wattage lamp becomes very hot during operation. Please observe the following precautions: • Never place objects on top of the projector while it is in operation. • Make sure there is an unobstructed space of 1,000 mm (39-3/8 in) or more around the projector’s exhaust openings. • If stacking projector units, care must be taken to provide the recommended space between units. These space requirements also apply to installation where only one projector unit is operating at one time and the other unit is used as a backup. • If the projector is placed in a box or enclosure, the temperature of the air surrounding the projector must match the operating temperature listed in the specifications table during use. Also, make sure the projector’s intake and exhaust openings are not blocked. Ensure there is sufficient ventilation to prevent hot air from the exhaust openings being recirculated into the intake opening. 3 The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods. • The lamp replacement cycle varies greatly depending on individual lamp characteristics and usage conditions. • The brightness of the lamp will gradually decrease with use. 4 Due to natural characteristics of lamps, screen brightness may fluctuate. This is not an indication of faulty lamp performance.