ERV DC Series

ERV DC Series

24-Hour, Efficient Ventilation for Large Spaces

24-hour continuous ventilation enables the constant circulation of fresh air. Energy Recovery Ventilator is efficient and energy-saving. Suitable for large spaces.

ERV DC Series

Features

Energy Efficient Energy Recovery During Ventilation

Panasonic’s ERV system recovers approximately 75% of energy released during circulation, reducing air conditioning loads, as well as energy usage.

Utilising counter flow heat exchange elements, energy released during the exhaust process of air conditioning is recovered and used alongside the supply of fresh air into commercial and residential locations. Reducing energy usage and thermal energy lost in other ventilation cycles.

Energy efficient DC motor

Our ERV systems utilise DC (Direct Current) motors to reduce power consumption of energy during use. Panasonic’s DC motors have a lower temperature rise than traditional AC (Alternating Current) motors, allowing for longer run times.

Energy Saving by Reducing Air Conditioner Load

Panasonic ERV systems allows for the reduction of thermal energy when paired with air conditioning systems. Allowing for up to 66% reduction of workload allowing for energy saving and energy efficient operation.
(Example: FY-E15DZ1)

The Filter Removes Dust, Pollen, and Other Harmful Particles, Allowing Only Clean Air to Enter The Room.

Did you know that we spend nearly 90% of our time indoors, inhaling around 18 kilograms of air every single day? This makes it crucial to prioritize clean and high-quality indoor air quality to create a healthier, more comfortable living environment.

Merv16/F7 standard filter designed to remove dust, pollen and other harmful particle’s, allowing only clean and purified air into the home.

Unified Control with Commercial Air Conditioners

Panasonic’s ERV system can be interconnected with most traditional air conditioning systems* allowing for energy efficient operations as well as automated systems to prevent energy loss during and after use.

*Method of connection depends on the model used

Unified Control with Commercial Air Conditioners

Highly Secure Fuse

Experience peace of mind with our advanced thermal safety fuse, designed to prevent accidents even during unexpected current surges of power.

Adjustable Airflow as Required

Optimise your airflow management by choosing between HIGH or LOW settings to precisely align with your environment's specific needs.

*1-4 among High and 1-4 among Low can be selected at the time of construction according to the building’s ventilation requirements.

Specs

FV-35ZY1

All maintenance can be performed through a single inspection hole

Straight air supply/exhaust system used for easier installation

			FV-35ZY1	FV-50ZY1	FV-65ZY1	FV-1KZY1	FV-1HZY1	FV-2KZY1
Air Volume (CMH)	High		350	500	650	1000	1500	2000
Air Volume (CMH)	Low		210	300	390	600	900	1200
Static Pressure (Pa)	High		140	130	150	150	130	130
Static Pressure (Pa)	Low		50.5	47	54	54	48	48
Temperature exchange efficiency (%)	High	Cooling	71	65	64	65	63	65
	High	Heating	83	81	82	82	83	82
	Low	Cooling	76	74	68	73	73	73
	Low	Heating	84	82	84	85	85	85
Enthalpy exchange efficiency (%)	High	Cooling	67	62.5	62.5	63	63.5	63
	High	Heating	75	73	66	74	73	74
	Low	Cooling	69	68	72	69	68	69
	Low	Heating	76	76	75	76	75	76
Power Consumption (W)	High		141	180	420	550	940	1100
Power Consumption (W)	Low		58	76	180	235	430	490
Noise Level (dB[A])	High		39	43	45	46	49	51
Noise Level (dB[A])	Low		33	32	34	36	41.5	43.5
Applicable Duct Diameter (mm)			φ150	φ200	φ200	φ250	φ250	φ250
Weight (kg)			37	40	48	64	116	139
Note			Note1: The value in Specification table are representative characteristics value at 220V, 50Hz. Note2: The input power and exchange efficiency are the values measured under the standard air volume. Note3: The above specification are the values measured under the factory set. Note4: The power indicated on the name plate is the maximum value under the static pressure of 0Pa. Note5: The noise is measured 1.5m directly below the center of the energy recovery ventilator. The noise value of the product is measured in a full anechoic chamber. Under actual conditions, due the impact of ambient sound, the noise value will be greater than the target value. The noise rises by about 1 dB(A) under reverse installation. Note6: The air volume in normal ventilation mode is basically the same as the air volume in energy recovery mode. Note7: The energy recovery efficiency test should be performed according to the method specified in Appendix 4 of JIS B 8628 (2003). The test environmental conditions should be subject to the winter and summer conditions specified in Table1 and Table2 of JIS B 8628 (2017). Other test methods should be subject to JIS B 8628 (2003).	Note1: The value in Specification table are representative characteristics value at 220V, 50Hz. Note2: The input power and exchange efficiency are the values measured under the standard air volume. Note3: The above specification are the values measured under the factory set. Note4: The power indicated on the name plate is the maximum value under the static pressure of 0Pa. Note5: The noise is measured 1.5m directly below the center of the energy recovery ventilator. The noise value of the product is measured in a full anechoic chamber. Under actual conditions, due the impact of ambient sound, the noise value will be greater than the target value. The noise rises by about 1 dB(A) under reverse installation. Note6: The air volume in normal ventilation mode is basically the same as the air volume in energy recovery mode. Note7: The energy recovery efficiency test should be performed according to the method specified in Appendix 4 of JIS B 8628 (2003). The test environmental conditions should be subject to the winter and summer conditions specified in Table1 and Table2 of JIS B 8628 (2017). Other test methods should be subject to JIS B 8628 (2003).	Note1: The value in Specification table are representative characteristics value at 220V, 50Hz. Note2: The input power and exchange efficiency are the values measured under the standard air volume. Note3: The above specification are the values measured under the factory set. Note4: The power indicated on the name plate is the maximum value under the static pressure of 0Pa. Note5: The noise is measured 1.5m directly below the center of the energy recovery ventilator. The noise value of the product is measured in a full anechoic chamber. Under actual conditions, due the impact of ambient sound, the noise value will be greater than the target value. The noise rises by about 1 dB(A) under reverse installation. Note6: The air volume in normal ventilation mode is basically the same as the air volume in energy recovery mode. Note7: The energy recovery efficiency test should be performed according to the method specified in Appendix 4 of JIS B 8628 (2003). The test environmental conditions should be subject to the winter and summer conditions specified in Table1 and Table2 of JIS B 8628 (2017). Other test methods should be subject to JIS B 8628 (2003).	Note1: The value in Specification table are representative characteristics value at 220V, 50Hz. Note2: The input power and exchange efficiency are the values measured under the standard air volume. Note3: The above specification are the values measured under the factory set. Note4: The power indicated on the name plate is the maximum value under the static pressure of 0Pa. Note5: The noise is measured 1.5m directly below the center of the energy recovery ventilator. The noise value of the product is measured in a full anechoic chamber. Under actual conditions, due the impact of ambient sound, the noise value will be greater than the target value. The noise rises by about 1 dB(A) under reverse installation. Note6: The air volume in normal ventilation mode is basically the same as the air volume in energy recovery mode. Note7: The energy recovery efficiency test should be performed according to the method specified in Appendix 4 of JIS B 8628 (2003). The test environmental conditions should be subject to the winter and summer conditions specified in Table1 and Table2 of JIS B 8628 (2017). Other test methods should be subject to JIS B 8628 (2003).	Note1: The value in Specification table are representative characteristics value at 220V, 50Hz. Note2: The input power and exchange efficiency are the values measured under the standard air volume. Note3: The above specification are the values measured under the factory set. Note4: The power indicated on the name plate is the maximum value under the static pressure of 0Pa. Note5: The noise is measured 1.5m directly below the center of the energy recovery ventilator. The noise value of the product is measured in a full anechoic chamber. Under actual conditions, due the impact of ambient sound, the noise value will be greater than the target value. The noise rises by about 1 dB(A) under reverse installation. Note6: The air volume in normal ventilation mode is basically the same as the air volume in energy recovery mode. Note7: The energy recovery efficiency test should be performed according to the method specified in Appendix 4 of JIS B 8628 (2003). The test environmental conditions should be subject to the winter and summer conditions specified in Table1 and Table2 of JIS B 8628 (2017). Other test methods should be subject to JIS B 8628 (2003).	Note1: The value in Specification table are representative characteristics value at 220V, 50Hz. Note2: The input power and exchange efficiency are the values measured under the standard air volume. Note3: The above specification are the values measured under the factory set. Note4: The power indicated on the name plate is the maximum value under the static pressure of 0Pa. Note5: The noise is measured 1.5m directly below the center of the energy recovery ventilator. The noise value of the product is measured in a full anechoic chamber. Under actual conditions, due the impact of ambient sound, the noise value will be greater than the target value. The noise rises by about 1 dB(A) under reverse installation. Note6: The air volume in normal ventilation mode is basically the same as the air volume in energy recovery mode. Note7: The energy recovery efficiency test should be performed according to the method specified in Appendix 4 of JIS B 8628 (2003). The test environmental conditions should be subject to the winter and summer conditions specified in Table1 and Table2 of JIS B 8628 (2017). Other test methods should be subject to JIS B 8628 (2003).

Documents

EnergyRecoveryVentilator DCSeries catalog EN (PDF - 1.9 MB)

ERV DC Series

24-Hour, Efficient Ventilation for Large Spaces

Features